How you can Install the Quick-Release Push-Button Lock for Your Window Guard

Attach the Strike Pin in your window guard

Typically the Strike Pin (3) should be forever mounted on or close to the outer steel framing with the home window guard -referred to be able to from now upon as WG- on the side of the WG’s “door” opposite regarding the hinge, near the middle (the same place where a doorknob is situated on a door). This should extend outward from the WG toward the wall membrane, so that it will later fall into the Lock Box tip-first when closed.

IMPORTANT: The particular Strike Pin need to point straight as you possibly can, ie not directed slightly up, along, to the kept, or to the correct. The straighter it really is, the smoother their operation later.

The spine of the Strike Pin has strings to get a 1/4″ bolt, so a commonplace way of affixing the strike green to your WG through first attaching a 1/4″ bolt it, then screwing the Strike Flag into that. Even so, a person want people being able to simply unscrew the bolt from the outside, it is therefore important that an individual permanently repair it to be able to the WG. This is certainly most often carried out by spot welding the attached Strike Pin set up, but if a welder isn’t handy, any way the bolt may be made unturnable will work, such as using one-way bolts.

Support the Window Shield

If this isn’t currently, it’s time to mount the WG on your window. Attach the Fasten Box (1) for the end of your pin so that will it locks set up. If it will not, ensure it is usually unlocked first simply by pushing the conclusion associated with the Push Fishing rod (2) into the particular smaller hole of the Lock Package first. This Lock Field will be installed to the outside wall of your building, so that you require to install typically the WG in a new position where the Lock Box could be mounted using the leading and bottom mess holes, and should not be pryed off (such as when that sits off the edge of any window frame).

push button box The other issue to keep inside mind this is that there will end up being an approximately 1/2″ hole drilled by means of your wall situated in the center of the Fastener Box, and the inside of typically the building, a a single 5/8″ diameter Flange will mount to be able to the wall close to that hole. So when you put up the WG, an individual want the Lock Box to end up being nearby the window beginning, but far more than enough enabling this 1/2″ hole to always be drilled from the wall, and hopefully get clear of any inner wall obstructions (like inside framing) for a 1 5/8″ diameter close to the hole center.

Mark your gap

With the Affect Pin attached to be able to your WG, plus the WG attached to your building, the remaining is relatively very simple!

Now we want to mark the location where the hole will become drilled through the wall so that it complements the small hole on the back of the Locking mechanism Box. First, force the Push Rod (2) in the Lock Box hole as a result it releases from the Strike Pin, and remove it. Place the Cardboard Go (4) all the way upon the Strike Pin, and cut off the particular end with the knife so typically the cardboard only barely extends beyond the Strike Pin. Close the WG door slowly till the round of cardboard complies with the wall, next use a pencil to draw a circle where this lands.

Drill

Technically a 3/8″ punch bit will get just right for the particular Push Rod in order to fit into, nevertheless I recommend some sort of 1/2″ bit, which usually leaves more room for error, and even is covered up just fine. Using the circle you just marked, drill the hole straight through your building wall membrane until you breach the other side.

At this point, reattach the Lock Box to the WG and maintain it closed. An individual from the inside should be in a position to put their own eye through the freshly drilled hole plus see the ENTIRE small hole associated with the Lock Field. If it is definitely partially covered, drill your hole till which clear course to it.

Mount the Lock Container

If it is not already, reattach typically the Lock Box to the WG and hold it closed. Indicate the upper in addition to lower holes of the Lock Box with your reliable pencil, then wide open the WG plus drill them using the drill little bit (NOT the large one! ) of which matches the anchoring screws you’re going to be able to use to mount the Lock Container, which don’t come with the kit. These types of screws should become between 1/4″ plus 3/8″, and should be about 2″ to 3″ extended.

With your a couple of holes drilled over and below your own BIG one, remove the Lock Box through the WG (you recognize how by now, appropriate? ), place that on the wall membrane, and mount this with your screws. Screw them within until they’re cuddle, but do not completely make tighter as of this time.

Align the particular Lock Box

Slowly and gradually close the WOHNGEMEINSCHAFT communicate mounted Locking mechanism Box, being careful Never to lock that in place. What’s that will? You say the Strike Pin isn’t very lining up? Take a chill pill, I am getting there.

With your hammer, smack the Lock Box sufficient to move that within the direction that needs to go. In the event that it won’t move, you screwed that in a tad too tight in addition to will need to be able to loosen it. Any time it is aligned properly, you may lock it inside place to make sure that works. It could be unlocked, associated with course, by staying the Push Fly fishing rod (2) through typically the hole in typically the wall until it launches. Note that you may want to “fish” around to the smaller hole in the Lock Box to push it in almost all the way.

Whenever everything is padded up, tighten typically the Lock Box screws all the approach. If everything is well aligned, the particular Push Rod ought to easily open typically the WG and the WG should easily lock in place. Even with the screws usually are tightened, you may be capable of work with the hammer with regard to final adjustments.

Leave a Reply

Your email address will not be published. Required fields are marked *